謝旻甫教授
專長與目前研究

獲獎、榮譽及學會職務
研究領域

1雙饋磁阻發電機

一般風力/水力發電機容易因風速/流速劇烈變化而影響電網電力品質,由本實驗室所發展的雙饋式設計即可改善上述缺點,主要針對此電機複雜的雙繞組匹配進行前期設計邏輯開發與驗證。

2高效率同步磁阻電機

IE4為目前國際能源效率之最高等級,本實驗室主要透過磁路分析與模擬驗證進行轉子研究設計,同時使考量不同材料,探討材料對電機性能的影響,並建立數值資料庫,以提升國內之高效率同步磁阻電機設計能量。

3高速渦輪發電機

日本於2014年定調高速電機為未來發展之主軸重點;當電機操作於高速狀態時,許多參數的細微變化均可能影響系統表現,本實驗室就高速渦輪發電機研究重點則依實際負載條件進行電機設計,並基於業者加工與成本考量提升運作效率;另一研究重點則結合結構振動與疲勞極限進行耦合分析,以達到系統整體性之設計考量。

4大功率動力馬達後充磁

製作磁鐵的稀土原料國際價格趨於穩定,為求產品結構的輕量化,大功率動力系統多以永磁式電機作為開標的,而稀土的高強度磁能特性又不利於組裝,本實驗室所發展之「後充磁」技術即可結合電機設計法來解決大型永磁電動機之組裝問題。
研究領域

1雙向驅動器設計開發

雙向驅動器設計開發:因應低能耗與高效率之產品開發趨勢,整合式啟動-發電機(Integrated Starter Generator, ISG)逐漸取代過去的直流有刷啟動馬達與發電機;除了設計上須滿足不同操作模式應有的性能外,更需一組可使電機操作於正確模式的驅動器,以方便就原始設計進行性能調校與提升

2切換式磁阻馬達漣波抑制

切換式磁阻馬達漣波抑制:切換式磁阻馬達(Switched Reluctance Motor, SRM)具有結構簡單、轉矩大、成本低等優點,但雙凸極結構造成大轉矩漣波與高噪音等問題;本實驗室則透過伺服迴路中外掛疊代學習控制器以處理高度非線性的電氣/磁路行為,並對電流進行補償達到抑制漣波的目的。

3電子電路與電機耦合

過去電動機在設計階段中,多將驅動模組與電機本體進行各別考量,待硬體實現後再進行相關參數調校;本實驗室所發展之電子電路/電機本體耦合分析開發技術則可於設計端便能有效預測控制指令/電子電路對電動機之操作行為,以提高設計準確度,並減低未來原型件之調效時間成本。
研究領域

造波機

本實驗室之造波機使用了大功率之伺服馬達配合螺桿驅動造波板,有高響應與高控制性能;由於造波範圍所需功率極大,使用四組伺服馬達共同推動一造波板,其單組伺服馬達38 kW(四組共152 kW);以網路式控制架構降低干擾,避免造成四組馬達不同步而損壞機構。因實驗無法製造不規則波,在波浪負載快速變動情形下,雖四組馬達同時接收控制器命令,但彼此間並未有控制上之耦合。故本實驗室對此進行控制系統整合設計,使其滿足製造不規則波之需求,開發自主性多軸同動不規則波造波控制器。

圖一 造波機

圖二 造波機網路式大功率伺服馬達

圖三 搖板式造波機

圖四 造波機構造圖

研究領域

1波浪發電系統

沉箱內波浪能擠壓空氣柱成為風能,再利用風能去推動葉片使發電機轉動而產生電力之系統。

圖一 系統架構圖

圖二 發電系統整合設計


2風力發電機


3UAV發電機與控制電路

研究成果

國外期刊論文

T.A. Huynh and M.-F. Hsieh*, “Comparative Study of PM-assisted SynRM and IPMSM on Constant Power Speed Range for EV Applications,” IEEE Transactions on Magnetics (accepted), vol. 53, no. 11, 2017. (SCI) (MOST 105-2622-8-006-001, MOST105-2218-E-006-008)
C. Ubadigha, M.-C. Tsai and M.-F. Hsieh, “Modulating ring structural configuration influence on the dual air-gap magnetic gear electric machine,” IEEE Transactions on Magnetics(accepted), vol. 53, no. 11, 2017 (SCI)
T. A. Huynh and M.-F. Hsieh*, "Performance Evaluation of Thin Electrical Steels Applied to Interior Permanent Magnet Motor," IEEJ Journal Industry Applications (accepted), vol. 11, 2017. (EI) (MOST 105-2622-8-006-001, MOST105-2218-E-006-008)
F.‐S. Pai, M.-F. Hsieh* and Y.‐P. Wang, “Cumulative current‐magnetizing method for a capacitor‐discharged impulse magnetizer,” International Journal of Circuit Theory and Applications, published online in Mar, 2017. (DOI: 10.1002/cta.2341) (SCI) (105-2623-E-024-001-ET)
C.-H. Hsu, Y.-M. Huang, M.-F. Hsieh, C.-M. Fu, S. Adireddy and D.B. Chrisey, “Transformer Sound Level Cause from Core Magnetostriction and Winding Stress Displacement Variation,” AIP Advances 7, 056681, 2017. (SCI).
M.-S. Wang, M.-F. Hsieh, Y.-S. Kung and G.-T. Lin, “Maximum Torque per Ampere Control of IPMSM Drive by Fuzzy Logic,” Microsystem Technologies, published online in Sep 2016. (DOI: 10.1007/s00542-016-3119-5) (SCI) (MOST 104-2221-E-218-025)
M.-S. Wang, M.-F. Hsieh, I.N. Syamsiana and W.-C. Fang, “Fuzzy Maximum Torque per Ampere and Maximum Torque per Voltage Control of Interior Permanent Magnet Synchronous Motor Drive,” Sensors and Materials, vol. 29, no. 4, pp. 461-472, 2017. (SCI) (MOST 104-2221-E-218-025)
M.-F. Hsieh*, Y.-H. Chang and D.G. Dorrell, “Design and Analysis of Brushless Doubly Fed Reluctance Machine for Renewable Energy Applications,” IEEE Transactions on Magnetics, vol. 52, no. 7, 7422795, 2016. (SCI) (MOST 101-2628-E-006-016-MY3)
S. Wang, D.G. Dorrell, Y. Guo and M.-F. Hsieh, “Inductive Charging Coupler with Assistive Coils. IEEE Transactions on Magnetics,” vol. 52, no. 7, 7428937, 2016. (SCI).
D.G. Dorrell, J.K.H. Shek and M.-F. Hsieh, “The Development of an Indexing Method for the Comparison of Unbalanced Magnetic Pull in Electrical Machines,” IEEE Transactions on Industry Applications, vol. 52, no. 1, pp. 145-153, 2016. (SCI) (MOST 101-2923-M-007-003)
I.-H. Lin, M.-F. Hsieh*, H.-F. Kuo and M.-C. Tsai, “Improved Accuracy for Performance Evaluation of Synchronous Reluctance Motor,” IEEE Transactions on Magnetics, vol. 51, no. 11, 8113404, 2015. (SCI) (MOST 103-2622-E-006-037)
C.-C. Chiang, M.-F. Hsieh*, Y.-H. Li and M.-C. Tsai, “Impact of Electrical Steel Punching Process on the Performance of Switched Reluctance Motors,” IEEE Transactions on Magnetics, vol. 51, no. 11, 8113304, 2015. (SCI) (MOST 103-2622-E-006-037)
C.-H. Hsu, M.-F. Hsieh, C.-M. Fu and Y.-M. Huang, “Effects of Multicore Structure on Magnetic Losses and Magnetomechanical Vibration at High Frequencies,” IEEE Transactions on Magnetics, vol. 51, no. 11, 8402704, 2015. (SCI)
C.-H. Hsu, S.-L. Lee, C.-C. Lin, C.-S. Liu, S.-Y. Chang, M.-F. Hsieh*, Y.-M. Huang and C.-M Fu. “Reduction of Vibration and Sound-Level for a Single-Phase Power Transformer With Large Capacity,” IEEE Transactions on Magnetics, vol. 51, no. 11, 8403204, 2015. (SCI)
M.-F. Hsieh, C.-H. Hsu, C.-M. Fu and Y.-M. Huang, “Design of Transformer With High-Permeability Ferromagnetic Core and Strengthened Windings for Short-Circuit Condition,” IEEE Transactions on Magnetics, vol. 51, no. 11, 8403304, 2015. (SCI)
M. Eftekhari, M. Moallem, S. Sadri and M.-F. Hsieh, “Online Detection of Induction Motor's Stator Winding Short-Circuit Faults,” IEEE Systems Journal, vol. 8, no. 4, 1272-1282, 2014. (SCI)
C.-C. Chiang, A.M. Knight, M.-F. Hsieh, M.-G. Tsai, B. H. Liu, I.-G. Chen, Z.-L. Gaing and M.-C. Tsai, “Effects of Annealing on Magnetic Properties of Electrical Steel and Performances of SRM After Punching,” IEEE Transactions on Magnetics, vol. 50, no. 11, 8203904, 2014. (SCI) (MOST 102-2622-E-006-032)
M.-F. Hsieh*, I.-H. Lin and D.G. Dorrell, “An Analytical Method Combining Equivalent Circuit and Magnetic Circuit for BDFRG,” IEEE Transactions on Magnetics, vol. 50, no. 11, 8206605, 2014. (SCI) (MOST 101-2628-E-006-016-MY3)
Z.-L. Gaing, Y.-Y. Hsiah, M.-C. Tsai, M.-F. Hsieh and M.-H. Tsai, “Rigorous Design of a Switched Reluctance Motor Using a Hybrid Design Model,” Journal of International Conference on Electrical Machines and Systems, vol. 3, no. 3, 256-263, 2014. (EI) (MOST 101-2221-E-244-011)
M.-F. Hsieh*, D.G. Dorrell, C.-K. Lin, P.-T. Chen and P.Y.P. Wung, “Modeling and Effects of In Situ Magnetization of Isotropic Ferrite Magnet Motors,” IEEE Transactions on Industry Applications, vol. 50, no. 1, 364-374, 2014. (SCI).
Z.-L. Gaing, C.-H. Lin, M.-H. Tsai, M.-F. Hsieh and M.-C. Tsai, “Rigorous Design and Optimization of Brushless PM Motor Using Response Surface Methodology with Quantum-Behaved PSO Operator,” IEEE Transactions on Magnetics, vol. 50, no. 1, 4002704, 2014. (SCI) (MOEA 100-EC-17-A-05-S1-192)
M. Eftekhari, M. Moallem, S. Sadri and M.-F. Hsieh, “A Novel Indicator of Stator Winding Inter-turn Fault in Induction Motor Using Infrared Thermal Imaging,” Infrared Physics & Technology, vol. 61, pp. 330-336, 2013. (SCI).
D. G. Dorrell, J. K. H. Shek, M. A. Mueller and M.-F. Hsieh, “Damper Windings in Induction Machines for Reduction of Unbalanced Magnetic Pull and Bearing Wear,” IEEE Transactions on Industry Applications, vol. 49, no. 5, pp. 2206-2216, 2013. (SCI).
M.-F. Hsieh*, Y.-C. Hsu, D. G. Dorrell and P.-T. Chen, “Evaluation of Permanent Magnet Generator Manufactured Using Post-Assembly Magnetization,” IEEE Transactions on Magnetics, vol. 49, no. 7, pp. 4084-4087, 2013. (SCI) (NSC 101-3113-E-006-003)
M.-F. Hsieh* and Y.-H. Yeh, “Rotor Eccentricity Effect on Cogging Torque of PM Generators for Small Wind Turbines,” IEEE Transactions on Magnetics, vol. 49, no. 5, pp. 1897-1990, 2013. (SCI) (MOST 101-3113-E-006-003)
M.-F. Hsieh*, C.-K. Lin and I.-H. Lin, “Design and Analysis of High Temperature Superconducting Generator for Offshore Wind Turbines,” IEEE Transactions on Magnetics, vol. 49, no. 5, pp. 1881-1884, 2013. (SCI).
M.-F. Hsieh*, I.-H. Lin and D. G. Dorrell, “Magnetic Circuit Modeling of Brushless Doubly-Fed Machines with Induction and Reluctance Rotors,” IEEE Transactions on Magnetics, vol. 49, no. 5, pp. 2359-2362, 2013. (SCI) (MOST 101-2628-E-006-016-MY3)
M.-F. Hsieh*, Y.-C. Hsu and P.-T. Chen, “Analysis and Experimental Study of Permanent Magnet Machines with In-situ Magnetization,” IEEE Transactions on Magnetics, vol. 49, no. 5, pp. 2351-2354, 2013. (SCI) (MOST 101-3113-E-006-003)
M.-F. Hsieh* and W.-C. Chang, “Combining Full and Semi Closed Loop Synchronous Control for Dual Mechanically Coupled Ball Screw System,” International Journal of Computer Applications in Technology, vol. 45, no. 2/3, pp. 139-147, 2012. (EI) (MOST 98-2815-C-006-045-E)
M.-F. Hsieh* and Y.-H. Yeh, “The Integrated Design of a Permanent-magnet Generator for Small Wind Energy Conversion System,” International Journal of Computer Applications in Technology, vol. 45, no. 2/3, pp. 98-105, 2012. (EI) (MOST 98-3114-E-006-011)
M.-F Hsieh*, I.-H. Lin, Y.-C. Hsu and R.A. McMahon, “Design of Brushless Doubly-Fed Machines Based on Magnetic Circuit Modeling,” IEEE Transactions on Magnetics, vol. 48, no. 11, pp. 3017–3020, 2012. (SCI) (MOST 100-2918-I-006-019)
M.-F. Hsieh*, F.-S. Hsu, and D.G. Dorrell, “Winding Changeover Permanent-Magnet Generators for Renewable Energy Applications,” IEEE Transactions on Magnetics, vol. 48, no. 11, pp. 4168-4171, 2012. (SCI) (MOST 98-2623-E-006-001-ET)
M.-F. Hsieh*, W.-S. Yao and C.-H. Hsu, “Modeling and Control of a Feed Drive with Multiple Mechanically Coupled Ball Screws,” Asian Journal of Control, vol. 14, no. 5, pp. 1227-1238, 2012. (SCI).
M.-F. Hsieh*, I.-H. Lin, D.G. Dorrell, M.-J. Hsieh and C.-C. Lin, “Development of a Wave Energy Converter Using a Two Chamber Oscillating Water Column,” IEEE Transactions on Sustainable Energy, vol. 3, no. 3, pp. 482–497, 2012. (SCI) (NSC100-2221-E-006-015, NSC 99-ET-E-006-007-ET)
Y.-H. Yeh, M.-F. Hsieh* and D.G. Dorrell, “Different Arrangements for Dual-Rotor Dual-Output Radial-Flux Motors,” IEEE Transactions on Industry Applications, vol. 48, no. 2, pp. 612-622, 2012. (SCI)
D.G. Dorrell, M.-F. Hsieh and A.M. Knight, “Alternative Rotor Designs for High Performance Brushless Permanent Magnet Machines for Hybrid Electric Vehicles,” IEEE Transactions on Magnetics, vol. 48, no. 2, pp. 835-838, 2012. (SCI)
M.-F. Hsieh* and Y.-C. Hsu, “A Generalized Magnetic Circuit Modeling Approach for Design of Surface Permanent-Magnet Machines,” IEEE Transactions on Industrial Electronics, vol. 59, no. 2, pp. 779-792, 2012. (SCI)
M.-F. Hsieh*, Y.-M. Lien and D.G. Dorrell, “Post-Assembly Magnetization of Rare-Earth Fractional-Slot Surface Permanent-Magnet Machines Using a Two-Shot Method,” IEEE Transactions on Industry Applications, vol. 47, no. 6, pp. 2478-2486, 2011. (SCI)
D.G. Dorrell, J. Shek, M.-F. Hsieh* and M.A. Mueller, “Unbalanced Magnetic Pull in Cage Induction Machines for Fixed-Speed Renewable Energy Generators,” IEEE Transactions on Magnetics, vol. 47, no. 10, pp. 4096-4099, 2011. (SCI)
Y.-S. Hsu, M.-C. Tsai and M.-F. Hsieh, “Sub-assembly Magnetization Strategies for a Transverse Flux Motor Equipped with Multiple NdFeB Magnet,” IEEE Transactions on Magnetics, vol. 47, no. 10, pp. 3681-3684, 2011. (SCI) (MOEA 99-EC-17-A-05-S1-103)
D. G. Dorrell, M.-F. Hsieh, M. Popescu, L. Evans, D. A. Staton and V. Grout, “A Review of the Design Issues and Techniques for Radial-Flux Brushless Surface and Internal Rare-Earth Permanent Magnet Motors,” IEEE Transactions on Industrial Electronics, vol. 58, no. 9, pp. 3741-3757, 2011. (SCI).
D. G. Dorrell, M. F. Hsieh and C. C. Lin, “A Multichamber Oscillating Water Column using Cascaded Savonius Turbines,” IEEE Transactions on Industry Applications, vol. 46, no. 6, pp. 2372-2380, 2010. (SCI)
Min-Fu Hsieh*, Hung-Ju Liao, “A Wide Speed Range Sensorless Control Technique of Brushless DC Motors for Electric Propulsors,” Journal of Marine Science and Technology, vol. 18, no 5, pp. 735-745, 2010. (SCI) (NSC 95-2221-E-006-471)
Min-Fu Hsieh*, You-Chiuan Hsu, David G. Dorrell, “Design of Large Power Surface-Mounted Permanent-Magnet Motors Using Post-Assembly Magnetization,” IEEE Transactions on Industrial Electronics, vol. 57, no. 10, pp. 3376-3384, 2010. (SCI)
David G. Dorrell, Min-Fu Hsieh and Chi-Chien Lin, “A Small Segmented Oscillating Water Column using a Savonius Rotor Turbine,” IEEE Transactions on Industry Applications, vol. 46, no. 5, pp. 2080-2088, 2010. (SCI)
D.G. Dorrell and M.-F. Hsieh, “Calculation of Radial Forces in Cage Induction Motors at Start - the Effect of Rotor Differential,” IEEE Transactions on Magnetics, vol. 46, no. 8, pp. 3029-3032, 2010. (SCI)
David G. Dorrell, Min-Fu Hsieh, Youguang Guo, “Unbalanced Magnet Pull in Large Brushless Rare-Earth Permanent Magnet Motors With Rotor Eccentricity,” IEEE Transactions on Magnetics, vol. 45, no. 10, pp. 4586-4589, 2009. (SCI)
M.F. Hsieh* and K.H. Hu, "Analysis of a Tubular Linear Motor with Soft Magnetic Composites for Reciprocating Compressors," Journal of Applied Physics, vol. 103, 07F 112, 2008. (SCI)
Y.S. Hsu, M.C. Tsai and M.F. Hsieh, "Novel Stator Design of Fan Motors Using Soft Magnetic Composites," Journal of Applied Physics, vol. 103, 07F 109, 2008. (SCI)
M.F. Hsieh*, C.J. Tung, W.S. Yao, M.C. Wu and Y.S. Liao, “Servo Design of a Vertical Axis Drive Using Dual Linear Motors for High Speed Electric Discharge Machining,” International Journal of Machine Tools and Manufacture, vol. 47, no. 3-4, pp. 546-554, 2007. (SCI) (NSC92-2213-E-006-095)
M.F. Hsieh* and Y.C. Hsu, “Characteristics Regulation for Manufacture of Permanent-Magnet Motors Using Post-Assembly Magnetization,” IEEE Transactions on Magnetics, vol. 43, no. 6, pp.2510-2512, 2007. (SCI) (NSC 95-2221-E-006-471)
M.F. Hsieh*, Y.C. Hsu, D.G. Dorrell and K.H. Hu, “Investigation on End Winding Inductance in Motor Stator Windings,” IEEE Transactions on Magnetics, vol. 43, no. 6, pp. 2513-2515, 2007. (SCI) (NSC 95-ET-7-006-008-ET)
D.G. Dorrell, M.F. Hsieh and Y.C. Hsu, “Post Assembly Magnetization Patterns in Rare Earth Permanent Magnet Motors,” IEEE Transactions on Magnetics, vol. 43, no. 6, pp. 2489-2491, 2007. (SCI)
M.F. Hsieh*, W.S. Yao and C.R. Chiang, “Modeling and Synchronous Control of a Single-Axis Stage Driven by Dual Mechanically-Coupled Parallel Ball Screws,” The International Journal of Advanced Manufacturing Technology, vol. 34, no.9-10, pp. 933-943, 2007. (SCI)
M.F. Hsieh*, Y.C. Lai, A. Horng and M.C. Tsai, “An Efficient Approach for Cogging Torque Analysis of Motors with Three-Dimensional Flux Distribution,” IEEE Transactions on Magnetics, vol. 42, no. 10, pp. 3464-3466, 2006. (SCI)
M.F. Hsieh* and Y.S. Hsu, “An Investigation on Influence of Magnet Arc Shaping upon Back Electromotive Force Waveforms for Design of Permanent-Magnet Brushless Motors,” IEEE Transactions on Magnetics, vol. 41, no. 10, pp. 3949–3951, 2005. (SCI) (NSC 93-2611-E-006-020)
M.C. Tsai, M.H. Weng and M.F. Hsieh, “Computer-Aided Design and Analysis of a Novel Fan Motor,” IEEE Transactions on Magnetics, vol. 38, no. 5, pp. 3467-3474, 2002. (SCI)
M.F. Hsieh, D.N. Moreton, J. Mistry and D.G. Moffat, “Limit Loads for Knuckle-encroaching Nozzles in Torispherical Heads: Experimental Verification of FE Predictions,” Journal of Strain Analysis, vol. 37, no. 4, pp. 313-326, 2002. (SCI)
D.G. Moffat, M.F. Hsieh and M. Lynch, “An Assessment of ASME III and CEN TC54 Methods of Determining Plastic and Limit Loads for Pressure System Components,” Journal of Strain Analysis, vol. 36, no. 3, 2001. (SCI)
M.F. Hsieh, D.G. Moffat and J. Mistry, “Nozzles in the Knuckle Region of a Torispherical Head: Limit Load Interaction under Combined Pressure and Piping Loads,” International Journal of Pressure Vessels and piping, vol. 77, pp. 807-815, 2001. (SCI)
M.F. Hsieh, D.G. Moffat and J. Mistry, “Nozzles in the Knuckle Region of a Torispherical Head: Stress Levels and Load Interaction Effects,” Journal of Process Mechanical Engineering (Proceedings of the Institution of Mechanical Engineers Part E), vol. 214, pp. 31-41, 2000. (SCI)
M.-C. Tsai, C.-C. Chou and M.-F. Hsieh, "Development of a real-time servo control test bench," IEEE Transactions on Education, vol. 40, no. 4, pp. 242-252, 1997. (SCI)

國內期刊論文

金書安、謝旻甫*(2016年05月)。磁鐵輔助之同步磁阻馬達效率與轉矩提升效益分析。機械月刊,05月,頁56-68。。本人為通訊作者。
翁佑甯、蔡逸文、謝旻甫*(2014年08月)。同步磁阻電機之特性分析。電機月刊,頁98-113,2014年8月號。本人為通訊作者。
江瑞利、帥俊銘、謝旻甫、蔡名曉、王品娟(2014年04月)。55kW級高功率車用磁阻動力馬達之設計與優化。機械月刊,2014年04月號。
江瑞利、胡家勝、郭冠毅、謝旻甫、蔡名曉(2013年08月)。高轉速磁阻馬達設計與最佳化--使用軟磁複合材料。電機月刊,頁86-98,2013年8月。
余守龍、謝旻甫*(2013年07月)。應用於無人飛行載具之整合式起動馬達-發電機研發。機械工業雜誌,頁83-96,2013年7月號。本人為通訊作者。
江瑞利、謝曜陽、謝旻甫、蔡名曉(2013年07月)。運用混合設計策略進行切換式磁阻馬達之優化設計。機械工業雜誌,頁42 -54,2013年7月號。
許裕昇、金書安、謝旻甫(2013年04月)。非稀土聚磁型永磁同步馬達磁路設計。機械月刊。本人為通訊作者。
白富升、謝旻甫、李威廷、張偉隆(2013年01月)。使用於一體式起動馬達發電機之雙向電能轉換電路設計。電機月刊。
謝銘峻、謝旻甫(2010年05月)。Darrieus風機葉片數與扭轉角度對風機性能的影響。風電月刊(WindPower),pp.16-27。本人為通訊作者。
謝旻甫、余守龍(2009年05月)。高效率永磁無刷馬達之設計與分析。電機月刊,No.221,P.140。本人為第一作者、通訊作者。
蔡明祺,蕭仕偉,謝旻甫,顛覆傳統的馬達--超音波馬達,科學發展月刊367期,2003年7月。
姚武松,蔡明祺,李榮顯,謝旻甫,多軸線性馬達驅動伺服系統設計,機械月刊第332期,2003年3月。(NSC 90-2212-E-006-100)
研究成果

國際研討會論文

Chang-Yi Cheng, Jia-Sheng Hu, Min-Fu Hsieh (2017, Nov). Energy Management System with Bi-directional Converter on Hybrid Sources Electric Scooters. 43th Annual Conference of the IEEE Industrial Electronics Society (IECON 2017), Beijing.
Thanh Anh Huynh, Min-Fu Hsieh, Kai-Jung Shih and Hsiu-Fu Kuo (2017, Aug). Design and Analysis of Permanent-Magnet Assisted Synchronous Reluctance Motor. 20th International Conference on Electrical Machines and Systems (ICEMS 2017), Sydney. (MOST 105-2622-8-006-001, MOST105-2218-E-006-008)
T.A. Huynh and M.-F. Hsieh* (2017, Apr). Comparative Study of PM-assisted SynRM and IPMSM on Constant Power Speed Range for EV Applications. 2017 INTERMAG, Dublin. (MOST 105-2622-8-006-001, MOST105-2218-E-006-008)
Min-Fu Hsieh*, Po-Ying Li, Hao-Yu Ting, Chung-Chan Hsu, Chin-Yang Chang, Wei-Che Lin, and Le-Ren Chang-Chien (2016, Nov). A Regenerative Braking System for Switched Reluctance Machine Applied to Electric Vehicles. 19th International Conference on Electrical Machines and Systems, Chiba. MOST 104-2218-E-006-026.
Thanh Anh Huynh and Min-Fu Hsieh* (2016, Nov). Performance Evaluation of Thin Electrical Steels Applied to Interior Permanent Magnet Motor. 19th International Conference on Electrical Machines and Systems, Chiba. MOST 104-2622-8-006-001.
Chien-Hsing Li and Min-Fu Hsieh* (2016, Aug). Multiphysics Analysis for Traction Motors Considering Electromagnetics, Noise, Vibration and Harshness. 4th International Conference of the Asian Union of Magnetics Societies, Tainan.
Min-Fu Hsieh*, Chung Chan Hsu, Hao-Yu Ting, Po-Ying Li, Le-Ren Chang-Chien and Yu-Hsien Li (2016, Aug). Improved Non-Linear Torque Sharing Function Applied to Torque Ripple Reduction of Switched Reluctance Motor. 4th International Conference of the Asian Union of Magnetics Societies, Tainan.
Min-Fu Hsieh*, Yao-Hsin Chang and David G Dorrell (2016, Jan). Design and Analysis of Brushless Doubly-Fed Reluctance Generator for Renewable Energy Applications. Joint MMM/INTERMAG Conference, San Diego.
Fu-Sheng Pai, Yi-Ping Wang, Chia-Chin Chou, Min-Fu Hsieh (2015, Oct). Magnetizing approach for permanent magnets with resonant power conversion. 2015 IEEE International Telecommunications Energy Conference, Osaka. MOST 103-2221-E-024-004.
M.F. Hsieh and S.L. Yu (2015, May). In-Situ Magnetization of Permanent Magnet Machines Considering Magnetizer Capacity and Connection Types. IEEE International Magnetics Conference (INTERMAG) 2015.
M.F. Hsieh, C.C. Chiang and M.C. Tsai (2015, May). Impact of Electrical Steel Punching Process on Performance of Switched Reluctance Motors. IEEE International Magnetics Conference (INTERMAG) 2015.
M.F. Hsieh, I.H. Lin and M.C. Tsai (2015, May). Improved Accuracy for Performance Prediction of Synchronous Reluctance Motor by Incorporating End Turn Inductance in 2-D FEM. IEEE International Magnetics Conference (INTERMAG) 2015.
M.F. Hsieh, I.W. Tsai and Y.N. Weng (2015, May). Cost-effective Design for High Efficiency Synchronous Reluctance Motor. IEEE International Magnetics Conference (INTERMAG) 2015.
I-Hsien Lin, Min-Fu Hsieh*, David G. Dorrell and Mi-Ching Tsai (2014, Oct). Dimension Effect on a Grid-connected Brushless Doubly-fed Reluctance Generator. The 17th International Conference on Electrical Machines and Systems (ICEMS2014, Hangzhou, China. MOST 101-2628-E-006-016-MY3.
Yao-Hsin Chang, Yi-Ting Li, I-Hsien Lin, Min-Fu Hsieh* (2014, Oct). A Design Approach Integrating the Magnetic Circuit and Electric Circuit Models for BDFIM. The 17th International Conference on Electrical Machines and Systems (ICEMS2014), Hangzhou, China. MOST 101-2628-E-006-016-MY3.
David G. Dorrell, Jonathan K.H. Shek, Min-Fu Hsieh (2014, Sep). The Development of an Indexing Method for the Comparison of Unbalanced Magnetic Pull in Electrical Machines. Energy Conversion Congress and Exhibition (ECCE), Pittsburgh.
Chao-Chien Chiang, Mu-Gong Tsai, Bernard Haochih Liu, In-Gann Chen, Andrew M. Knight, Mi-Ching Tsai, Zwe-Lee Gaing and Min-Fu Hsieh (2014, May). Effects of Annealing on Magnetic Properties of Electrical Steel and Performances of SRM After Punching. International Magnetics Conference (Intermag 2014), Dresden, Germany.
M.F. Hsieh, I.H. Lin and D.G. Dorrell (2014, May). An Analytical Method Combining Equivalent Circuit and Magnetic Circuit for a Brushless Doubly-Fed Reluctance Generators. Intermag, Dresden, Germany.
M.F. Hsieh, S.A. Chin, C.H. Lee, and M.C. Tsai (2014, May). Design of a High Torque Density Ferrite IPM Motor for Electric Vehicles with Coupled Electromagnetics and Stress Analysis. Intermag, Dresden, Germany.
Zwe-Lee Gaing, Jian-Yu Zhu, Min-Fu Hsieh, Mi-Ching Tsai and Ming-Hsiao Tsai (2014, May). Multi-Objective Optimization for a Permanent-Magnet- Assisted Synchronous Reluctance Motor Using Response Surface Method with SFLA Operator. International Magnetics Conference (Intermag 2014), Dresden, Germany.
M.-F. Hsieh and I.H. Lin (2013, May). Comparison of Brushless Induction and Reluctance Doubly-Fed Machines. 22nd IEEE International Symposium on Industrial Electronics, Taipei, Taiwan.
M.-F. Hsieh, I.H. Lin and D. G. Dorrell (2013, Jan). Comparison of Brushless Doubly-Fed Machines with Various Rotor Types. the 12th Joint MMM/Intermag Conference, Chicago.
M.-F. Hsieh, Y.C. Hsu and P.T. Chen (2013, Jan). Evaluation of Permanent Magnet Machines Manufactured Using Post-Assembly Magnetization. the 12th Joint MMM/Intermag Conference, Chicago.
M.-F. Hsieh, and C.-K. Lin (2013, Jan). Optimum Design of High Temperature Superconducting Generator for Offshore Wind Turbines. the 12th Joint MMM/Intermag Conference, Chicago.
M.-F. Hsieh and Y.H. Yeh (2012, Nov). Rotor Eccentricity Effect on Cogging Torque of PM Generators for Small Wind Turbines. the Fifteenth Biennial IEEE Conference on Electromagnetic Field Computation (CEFC2012), Oita.
M.-F. Hsieh, I.-H. Lin and D. G. Dorrell (2012, Nov). Design of Brushless Doubly-Fed Machine with Induction Rotor and Reluctance Rotor based on Magnetic Circuit Modeling. the Fifteenth Biennial IEEE Conference on Electromagnetic Field Computation (CEFC2012), Oita.
M.-F. Hsieh, Y.C. Hsu and P.T. Chen (2012, Nov). Analysis and Experimental Study of Permanent Magnet Machines with In-situ Magnetization. the Fifteenth Biennial IEEE Conference on Electromagnetic Field Computation (CEFC2012), Oita.
M.-F. Hsieh, and C.K. Lin (2012, Nov). Design and Analysis of High Temperature Superconducting Generator for Offshore Wind Turbines. the Fifteenth Biennial IEEE Conference on Electromagnetic Field Computation (CEFC2012), Oita.
M.-F. Hsieh, F.S. Hsu, and D.G. Dorrell (2012, May). Winding Changeover Permanent-Magnet Generators for Renewable Energy Applications. IEEE International Magnetics Conference, Vancouver.
M.-F. Hsieh, I.H. Lin, Y.C. Hsu and R.A. McMahon (2012, May). Design of Brushless Doubly-Fed Machines Based on Magnetic Circuit Modeling. IEEE International Magnetics Conference, Vancouver.
M.-F. Hsieh, I.H. Lin and W.Y. Chen (2011, Dec). Comparative Study on Performance of Savonius and Darrieus Turbines for a Wave Energy Converter using Oscillating Water Column. the 11th International Conference on Fluid Control (FLUCOME 2011), Keelung, Taiwan.
D. G. Dorrell, J. K. H. Shek, M. A. Mueller, M.-F. Hsieh (2011, Sep). Damper Windings in Induction Machines for Reduction of Unbalanced Magnetic Pull and Bearing Wear. IEEE Energy Conversion Congress and Exposition (ECCE).
J.K.H. Shek, D.G. Dorrell, M.-F. Hsieh, D.E. Macpherson, and M.A. Mueller (2011, Sep). Reducing Bearing Wear in Induction Generators for Wave and Tidal Current Energy Devices. IET Renewable Power Generation Conference.
M.-F. Hsieh, C.C. Lin and H.Y. Li (2011, Sep). Development of a Simulator for Control Design of a Wave Maker. The Society of Instrument and Control Engineers, Tokyo.
M.-F. Hsieh, C.K. Lin, D.G. Dorrell and P. Wung (2011, Sep). Modeling and Effects of In-Situ Magnetization of Isotropic Ferrite Magnet Motors. Energy Conversion Congress and Exhibition (ECCE 2011).
M.-F. Hsieh, H.Y. Li and K.Y. Lai (2011, Sep). Synchronous Control of a Network-Based Triple Mechanically-Coupled Ball Screws System. The Society of Instrument and Control Engineers, Tokyo.
D. G. Dorrell and M.-F. Hsieh (2011, Jul). Alternative Rotor Designs for High Performance Brushless Permanent Magnet Machines for Hybrid Electric Vehicles. Compumag 2011.
D. G. Dorrell, J. Shek, M. F Hsieh and M. A. Mueller (2011, Apr). Unbalanced Magnetic Pull in Cage Induction Machines for Fixed-Speed Renewable Generators. Intermag 2011, Taipei, Taiwan.
M.-F. Hsieh, Yao-Min Lien and David Dorrell (2010, Sep). Post-Assembly Magnetization of Rare-Earth Fractional-Slot Permanent-Magnet Machines using a Two-Shot Method. IEEE ECCE 2010, Atlanta.
M.-F. Hsieh, and I.H. Lin (2010, Sep). Application of a Marine Dynamic Positioning System Using CAN. the International Forum on Systems and Mechatronics (IFSM 2010), Singapore.
M.-F. Hsieh, and K.Y. Lai (2010, Sep). A Network-Based Real-Time Control System for Mechanically-Coupled Multi-Axis Servomechanism. the International Forum on Systems and Mechatronics (IFSM 2010), Singapore.
M.-F. Hsieh, and W.C. Chang (2010, Sep). Combining Full and Semi Closed Loop Synchronous Control for Dual Mechanically Coupled Ball Screw System. the International Forum on Systems and Mechatronics(IFSM 2010), Singapore.
M.-F. Hsieh, and Y.H. Yeh (2010, Sep). The Integrated Design of a Permanent- Magnet Generator for Small Wind Energy Conversion System. the International Forum on Systems and Mechatronics (IFSM 2010), Singapore.
Yu-Han Yeh, M.-F. Hsieh and David Dorrell (2010, Sep). Different Arrangements for Dual-Rotor Dual-Output Radial-Flux Motors. IEEE ECCE 2010, Atlanta.
D. G. Dorrell and M.-F. Hsieh (2010). Issues with Low Speed Direct-Drive Permanent-Magnet Generator Design – Comparison of Radial-Flux Slotted and Torus Machines. IECON 2010.
M.-F. Hsieh, D.G. Dorrell, Y.H. Yeh, and S. Ekram (2009, Nov). Cogging Torque Reduction in Axial Flux Machines for Small Wind Turbines. the 35rd Annual Conference of the IEEE Industrial Electronics Society (IECON’09), Porto.
M.-F. Hsieh, W.S. Yao and C.H. Hsu (2009, Nov). Modeling and Control of a Feed Drive with Multiple Mechanically Coupled Ball Screws. 2009 CACS International Automatic Control Conference, Taipei, Taiwan.
M.-F. Hsieh, Y.H. Yeh, D.G. Dorrell, and S. Ekram (2009, Nov). Reduction of Cogging Torque for Axial Flux Generator Applied to Small Wind Turbine. International Conference on Computation of Electromagnetic Field (Compumag 2009), Florianopolis.
M.-F. Hsieh, Y.H. Yeh, D.G. Dorrell, and Samsul Ekram (2009, Nov). Design of a Dual-Rotor Dual-Output Radial-Flux Motor for Variable Speed Air Conditioners. International Conference on Computation of Electromagnetic Field (Compumag 2009), Florianopolis.
Y.C. Hsu, M.-F. Hsieh, and R.A. McMahon (2009, Nov). A General Design Method for Electric Machines Using Magnetic Circuit Model Considering the Flux Saturation Problem. International Conference on Power Electronics and Drive Systems (PEDS 2009), Taipei, Taiwan.
D.G. Dorrell, C.C. Lin and M.-F. Hsieh (2009, Sep). A Multi-Chamber Oscillating Water Column using Cascaded Savonius Turbines. the IEEE ECCE Conference, San Jose.
M.-F. Hsieh, W.S. Yao and C.H. Hsu (2009, Jun). System Identification of a Feed Drive Composed of Multiple Mechanically-Coupled Ball Screws. the 10th International Conference on Automation Technology, Tainan, Taiwan.
M.-F. Hsieh, D.G. Dorrell, and Samsul Ekram (2009, May). Cogging Torque Reduction in Axial Flux Machines for Small Wind Turbines. the International Intermag Conference, Sacramento.
M.-F. Hsieh, Y.H. Yeh, D.G. Dorrell, and Samsul Ekram (2009, May). A Radial Flux Machine with Dual Rotors Dual Output Shafts for Variable Speed Air Conditioners. the International Intermag Conference, Sacramento.
M.F. Hsieh, W.S. Yao and C.H. Hsu, "System Identification of a Feed Drive Composed of Multiple Mechanically-Coupled Ball Screws," in Proceedings of Automation 2009, the 10th International Conference on Automation Technology, Tainan, Jun. 27-29, 2009.
M.F. Hsieh, D.G. Dorrell, and Samsul Ekram, "Cogging Torque Reduction in Axial Flux Machines for Small Wind Turbines," in Proceedings of the International Intermag Conference, Sacramento, May, 2009.
M.F. Hsieh, Y.H. Yeh, D.G. Dorrell, and Samsul Ekram, "A Radial Flux Machine with Dual Rotors Dual Output Shafts for Variable Speed Air Conditioners," in Proceedings of the International Intermag Conference, Sacramento, May, 2009.
C.C. Lin, D.G. Dorrell and M.F. Hsieh, "A Small Segmented Oscillating Water Column using a Savonius Rotor Turbine," in Proceedings of the 2008 IEEE International Conference on Sustainable Energy Technologies, Singapore, Nov. 24-27, 2008.
F.S. Pai, S.J. Huang, M.F. Hsieh and C.M. Lin, "Design of Modular Inverter for Distributed Power Generation," in Proceedings of the 2008 IEEE International Conference on Sustainable Energy Technologies, Singapore, Nov. 24-27, 2008.
D.G. Dorrell and M.F. Hsieh, " Performance of Wells Turbines for use in Small-Scale Oscillating Water Columns," in Proceedings of the Eighteenth International Offshore and Polar Engineering Conference (ISOPE), Vancouver, Canada, July 6 - 11, 2008.
M.F. Hsieh, Y.C. Hsu, and K.H. Hu, “Investigation on End Winding Inductance in Stators of Permanent-Magnet Motors,” Proceedings of the 10th MMM/Intermag Joint Conference, Jan. 2007. (NSC 95-ET-7-006-008-ET)
M.F. Hsieh and Y.C. Hsu, “Characteristics Regulation for Manufacture of Permanent-Magnet Motors Using Post-Assembly Magnetization,” Proceedings of the 10th MMM/Intermag Joint Conference, Baltimore, Jan. 7-11, 2007. (NSC 95-2221-E-006-471)
M.F. Hsieh, S.H. Wang and W.S. Yao, "Development of an Anti-Rolling Control System Using Linear Motors," in Proceedings of the 2nd International Forum on Systems and Mechatronics (IFSM 2007), December 3-6, Tainan, Taiwan.
M.F. Hsieh and I.J. Lin, "A CAN Bus-based Control System for Automatic Ship Positioning," in Proceedings of the 2nd International Forum on Systems and Mechatronics (IFSM 2007), December 3-6, Tainan, Taiwan.
M.F. Hsieh, T.L. Fu, and Y.C. Hsu, “Development of a Magnetic Driven Polishing System,” the 2nd International Forum on Systems and Mechatronics (IFSM 2007), December 3-6, Tainan, Taiwan. (NSC95-2815-C-006 -062 -E)
M.F. Hsieh, H.J. Liao and P.J. Wu, "A Sensorless Driving Technique for Propulsion of Small Electric Ships," in Proceedings of the 2nd International Forum on Systems and Mechatronics (IFSM 2007), December 3-6, Tainan, Taiwan.
M.F. Hsieh and K.H Hu, "Analysis of a Tubular Linear Motor with Soft Magnetic Composites for Reciprocating Compressors," in Proceedings of the 52nd Magnetism and Magnetic Materials Conference (MMM2007), November 5-9, 2007, Florida, USA.
Y.S. Hsu, M.C. Tsai and M.F. Hsieh, "Novel Stator Design of Fan Motors Using Soft Magnetic Composites," in Proceedings of the 52nd Magnetism and Magnetic Materials Conference (MMM2007), November 5-9, 2007, Florida, USA.
M.F. Hsieh, Y.C. Hsu and D.G. Dorrell, "Design of Large Power Surface-mounted Permanent-magnet Motors Using Post-assembly Magnetization Process," in Proceedings of the 33rd Annual Conference of the IEEE Industrial Electronics Society (IECON'07), Taipei, Taiwan, Nov. 5-8, 2007.
M.F. Hsieh, J.H. Chen, Y.H. Yeh, C.L. Lee, P.H. Chen, Y.C. Hsu, and Y.H. Chen, "Integrated Design and Realization of a Hubless Rim-driven Thruster," in Proceedings of the 33rd Annual Conference of the IEEE Industrial Electronics Society (IECON'07), Taipei, Taiwan, Nov. 5-8, 2007.
D.G. Dorrell, M.F. Hsieh and W. Fillet, “Segmented Small Oscillating Water Columns Using In-Line Savonius Rotors,” in Proceedings of the International Offshore and Polar Engineering Conference (ISOPE), Lisbon, July 1–6, 2007.
M.F. Hsieh, Y.C. Hsu and D.G. Dorrell, “Design of Large Power Surface-mounted Permanent-magnet Motors Using Post-assembly Magnetization Process,” the 33rd Annual Conference of the IEEE Industrial Electronics Society (IECON’07), Taipei, Taiwan, Nov. 5-8, 2007. (NSC 95-ET-7-006-008-ET)
M.F. Hsieh, J.H. Chen, Y.H. Yeh, C.L. Lee, P.H. Chen, Y.C. Hsu, and Y.H. Chen, “Integrated Design and Realization of a Hubless Rim-driven Thruster,” the 33rd Annual Conference of the IEEE Industrial Electronics Society (IECON’07), Taipei, Taiwan, Nov. 5-8, 2007. (NSC 95-2221-E-006-471)
D.G. Dorrell and M.F. Hsieh, “Post Assembly Magnetization Patterns in Rare Earth Permanent Magnet Motors,” Proceedings of the 10th MMM/Intermag Joint Conference, Jan. 2007.
M.F. Hsieh, M.C. Tsai, A. Horng and Y.C. Lai, “An Efficient Approach for Cogging Torque Analysis of Motors with Three-Dimensional Flux Distribution,” Proceedings of the International Magnetics Conference, San Diego, May, 2006.
M.F. Hsieh and Y.S. Hsu, “An Investigation on Influence of Magnet Arc Shaping upon Back Electromotive Force Waveforms for Design of Permanent-Magnet Brushless Motors,” Proceedings of the International Magnetics Conference (INTERMAG 2005), Japan, April 4-8, 2005. (NSC 93-2611-E-006-020)
B. H Shen, M.F. Hsieh, M. C. Wu, G. L. Hsu, C. R. Chiang and M. C. Tsai, “Synchronous Control of a Parallel Dual Inverted Pendulum System Driven by Linear Servomotors”, Proceedings of the IEEE International Conference on Hands-on Intelligent Mechatronics and Automation (HIMA 2005), Taipei, Taiwan, July, 2005.
M.F. Hsieh, W.S. Yao, and M.C. Wu, “Design of a Linear Servo System for the Vertical Axis of High Speed Electric Discharge Machining,” Proceedings of the International Symposium on Linear Drives for Industrial Applications (LDIA 2005), Japan, 2005. (NSC92-2213-E-006-095)
M.F. Hsieh and Y.C. Hsiu, “Characteristic Analysis for IPM Motors with Post-Assembly Magnetization,” Proceedings of the the Eighth International Conference on Electric Machines and Systems (ICEMS 2005), Nanjing, China, September, 2005. (NSC 94-2623-7-006-009-ET)
T.C. Chen, R.D. Lin, M. C. Tsai, M.F. Hsieh, Z.Q. Zhu, P.G. Stewart and D. Howe, “Fuzzy Control for Torque Ripple Reduction of a Switched Reluctance Motor with External Rotor,” Proceedings of the International Conference on Electrical Machines and Systems, Jeju, Korea, November, 2004. (NSC 92-2911-I-006-029)
S.W. Hsiao, M.C. Tsai, M.S. Tsai and M.F. Hsieh, “Stator Modeling of a Traveling Wave-type Ultrasonic Linear Motor,” Proceedings of the International Conference on Electrical Machines and Systems, Jeju, Korea, November, 2004.
M.F. Hsieh, K.Y. Lo, C.Y. Sun and M.C. Tsai, “Development of Automated Alignment Techniques for Coupling of Fiber Optic Components,” ASME Proceedings of the 7th Biennial Conference on Engineering Systems Design and Analysis, Manchester, UK, 2004.
M.C. Tsai, M.F Hsieh and W.S. Yao, “Synchronous Control of Linear Servo Systems for CNC Machine Tools,” Proceedings of the European Control Conference (ECC2003), Cambridge UK, September 2003. (NSC 90-2212-E-006-100)
M.F. Hsieh, D.G. Moffat and J. Mistry, “Nozzles in Klöpperböden Head: The influence of a nozzle size on stress levels and limit loads”, Proceedings of the 10th International Conference on Pressure Vessel Technology, Vienna, Austria, July 7-10, 2003.
J.X. Yang, M.C. Tsai and M.F Hsieh, “Identification and Control of a Linear Servo System,” Proceedings of the International Symposium on Linear Drives for Industry Applications (LDIA 2003), Birmingham UK, September 8-10, 2003. (NSC 90-2212-E-006-100)
Z.Q. Zhu, S. Long, D. Howe, M. C. Tsai, M. F. Hsieh and T. C. Chen, “Significance of Vibration Modes in Noise and Vibration Generation of Switched Reluctance Motors,” Proceedings of the International Conference on Electrical Machines and Systems, Beijing (ICEMS), November 8-11, 2003. (NSC 91-2911-I-006-013)
M.F. Hsieh, D.G. Moffat and J. Mistry, “Nozzles in the Knuckle Region of a Torispherical Head: Limit Load Interaction under Combined Pressure and Piping Loads,” Proceedings of the 9th International Conference on Pressure Vessel Technology, pp. 79-90, Sydney, 2000.

國內研討會論文

金書安、謝旻甫*(2016年05月)。磁鐵輔助之同步磁阻馬達效率與轉矩提升效益分析。機械月刊,05月,頁56-68。。本人為通訊作者。
翁佑甯、蔡逸文、謝旻甫*(2014年08月)。同步磁阻電機之特性分析。電機月刊,頁98-113,2014年8月號。本人為通訊作者。
江瑞利、帥俊銘、謝旻甫、蔡名曉、王品娟(2014年04月)。55kW級高功率車用磁阻動力馬達之設計與優化。機械月刊,2014年04月號。
江瑞利、胡家勝、郭冠毅、謝旻甫、蔡名曉(2013年08月)。高轉速磁阻馬達設計與最佳化--使用軟磁複合材料。電機月刊,頁86-98,2013年8月。
余守龍、謝旻甫*(2013年07月)。應用於無人飛行載具之整合式起動馬達-發電機研發。機械工業雜誌,頁83-96,2013年7月號。本人為通訊作者。
江瑞利、謝曜陽、謝旻甫、蔡名曉(2013年07月)。運用混合設計策略進行切換式磁阻馬達之優化設計。機械工業雜誌,頁42 -54,2013年7月號。
許裕昇、金書安、謝旻甫(2013年04月)。非稀土聚磁型永磁同步馬達磁路設計。機械月刊。本人為通訊作者。
白富升、謝旻甫、李威廷、張偉隆(2013年01月)。使用於一體式起動馬達發電機之雙向電能轉換電路設計。電機月刊。
謝銘峻、謝旻甫(2010年05月)。Darrieus風機葉片數與扭轉角度對風機性能的影響。風電月刊(WindPower),pp.16-27。本人為通訊作者。
謝旻甫、余守龍(2009年05月)。高效率永磁無刷馬達之設計與分析。電機月刊,No.221,P.140。本人為第一作者、通訊作者。
蔡明祺,蕭仕偉,謝旻甫,顛覆傳統的馬達--超音波馬達,科學發展月刊367期,2003年7月。
姚武松,蔡明祺,李榮顯,謝旻甫,多軸線性馬達驅動伺服系統設計,機械月刊第332期,2003年3月。(NSC 90-2212-E-006-100)
研究成果

專利

Tzu-Shien Chuang, Mi-Ching Tsai, Min-Fu Hsieh,"CURRENT VECTOR CONTROLLED SYNCHRONOUS RELUCTANCE MOTOR AND CONTROL METHOD THEREOF" (美國發明專利)
Cho-Nien Tung, Min-Fu Hsieh, Yu-Sheng Hsu, Mi-Ching Tsai and Lung-Wei Huang,"Fan" (美國發明專利)
Min-Fu Hsieh, Wan-Yu Wu, Hui-Chun Ho and Yee-Pien Yang,"STATOR STRUCTURE" (美國發明專利)
莊子賢、蔡明祺、謝旻甫,"電流向量控制的同步磁阻馬達驅動系統" (中華民國發明專利)
謝旻甫、白富升、蔡明祺、黃世杰、陳映蓉、王毅平,"電動機的充磁電路裝置" (中華民國發明專利)
謝旻甫、胡凱翔,"馬達" (中華民國發明專利)
謝旻甫、徐佑銓,"利用後充磁製作之永磁無刷馬達設計方法" (中華民國發明專利)
謝旻甫、姚武松、吳孟杰,"雙平行線型馬達同動控制系統" (中華民國發明專利)
謝旻甫、許裕昇、蔡明祺,"風扇之驅動模組" (中華民國發明專利)
謝旻甫、王盛篁、姚武松、黃正清,"船舶減搖裝置" (中華民國發明專利)
陳正虎,鄭銘揚,廖鴻儒,謝旻甫,蔡明祺,"三相無刷直流馬達之無感測器換相電路及三相換相信號檢測方法" (中華民國發明專利)
謝旻甫、孫嘉陽、羅光耀、蔡明祺、黃禹傑,"方向預判式尋光對位方法"(中華民國發明專利)
蔡明祺、姚武松、謝旻甫、楊君賢,"雙平行線性馬達同步控制器" (中華民國發明專利)
研究成果

相關計畫

計畫名稱
計畫時間
相關說明
高效率高轉速微渦輪發電機系統設計開發(III)
106/08/01-107/07/31
主持人
動力馬達熱磁耦合模型建立及模擬分析技術之研究
106/03/01-106/11/30
主持人
高效率高轉速微渦輪發電機系統設計開發(II)
105/08/01-106/07/31
主持人
異向性釹鐵硼環狀磁石於弦波控制之馬達應用研究
105/01/01-105/12/31
主持人
高性能步進馬達之共同開發
105/05/01-105/10/31
主持人
次世代鋼及其綠色製程與產品創新應用產學合作計畫(4/5)
105/08/01-106/07/31
主持人
高效率高轉速微渦輪發電機系統設計開發(I)
104/08/01-105/07/31
主持人
次世代鋼及其綠色製程與產品創新應用產學合作計畫(3/5)
104/08/01-105/07/31
主持人
客製化輕量高效率電動馬達研製
104/06/16-105/04/15
主持人
應用於水車之高效率高扭力橫流磁通馬達(TFM)設計
104/05/01-105/04/30
主持人
2.2KW主軸馬達開發
104/10/01-105/09/30
主持人
次世代鋼及其綠色製程與產品創新應用產學合作計畫(2/5)
103/08/01-104/07/31
主持人
750W及1kW伺服馬達開發
103/08/01-104/09/30
主持人
能源科技系列課程計畫
103/09/01-105/01/31
主持人
次世代鋼及其綠色製程與產品創新應用產學合作計畫(1/5)
102/08/01-103/07/31
主持人
Research on Torque Ripple Reduction of SR Motors
102/09/01-2016/03/31
主持人
先進無刷雙饋電機之泛用磁路模型建立及其於大型風機之應用(1/3)
101/08/01-102/07/31
主持人
先進無刷雙饋電機之泛用磁路模型建立及其於大型風機之應用(2/3)
102/08/01-103/07/31
主持人
先進無刷雙饋電機之泛用磁路模型建立及其於大型風機之應用(3/3)
103/08/01-104/07/31
主持人
基於即時網路之自主性多軸同動造波機控制系統設計(II)
100/08/01-101/07/31
主持人
基於即時網路之自主性多軸同動造波機控制系統設計(I)
99/08/01-100/07/31
主持人
有段式節能驅動器研究開發
100/04/01-100/10/31
主持人
岸基式多氣室震盪水柱波浪發電之系統設計與實現(I)
99/01/01-99/12/31
主持人
水下載具應用於海底管線檢修之關鍵技術研發-水面工作載台動態定位之推進器及驅動控制系統設計與實現
98/01/19-99/07/31
主持人
高效率變結構發電機於風力發電之設計實現(II)
98/01/01-98/12/31
主持人
高效率變結構發電機於風力發電之設計實現(I)
970101-971231
主持人
水下載具應用於海底管線檢修之關鍵技術研發-水面工作載台動態定位之推進器及驅動控制系統設計與實現(I)
97/08/01-99/07/31
主持人
水下載具應用於海底管線檢修之關鍵技術研發-水面工作載台動態定位之推進器及驅動控制系統設計與實現(II)
98/08/01-99/07/31
主持人
輔以電力調節器設計之漁船電力系統
97/06/01-97/12/31
主持人
水下載具應用於海底管線檢修之關鍵技術研發-水面工作載台動態定位之推進器及驅動控制系統設計與實現
96/08/01-97/07/31
主持人
高性能無刷直流馬達無感測器驅動系統之研製
96/11/01-97/10/31
主持人
智慧型電力調整器應用於漁船發電系統
96/05/08-96/12/31
主持人
自主性太陽能船系統開發之研究-子計畫三:自主性太陽能船之推進與監控系統整合設計(I)(II)
94/01/01-95/12/31
主持人
抗流型水下遙控載具(ROV)關鍵性技術開發暨系統整合-子計畫三:抗流型水下遙控載具高性能推進系統之研發(1/3, 2/3, 3/3)
93/08/01-96/07/31
主持人
高效率車用空調系統之鼓風機無刷馬達設計
95/11/01-96/10/31
主持人
漁船電力推進微電腦控制系統之研發
95/03/28-95/12/31
主持人
線性馬達驅動之高速工具機Z軸伺服系統之研究
92/12-93/07
主持人

實驗室介紹

[ 五樓研究生室 ]

本研究室為主要之研究生室。這裡為馬達設計組主要學習與研究之處。

[ 四樓研究生室 ]

本研究室為主要之研究生室。

[ B1實驗室 ]

本實驗室為系統系機電系統整合實驗室,為公共實驗室,以教學為主,研究為輔。本實驗室主要實驗設備放置於此。
活動花絮與照片

儀器設備


量測設備及各式機台

電機特性量測平台(5.5kW)

電機特性量測平台(2kW,高速)

電機特性量測平台(1Hp)

高斯計

LCR Meter

混合訊號示波器


控制器及控制卡

dsPIC微控制器發展板(多組)

DSP伺服控制卡(數張)

PIC微控制器發展板及模擬器(數十組)

TI DSP2407A 發展板/模擬器


馬達相關

IGBT模組

無刷直流馬達


助理
姓名
職位
專長
E-mail
黃明瑜
行政助理
1.行政 2.會計 3.test
anytajoe@gmail.com

學生

李建興

電機設計、震動噪音

楊承哲

電機驅動控制

黃成影

電機設計與磁性齒輪

吳德堅


鍾潤鴻


陳伯恒


楊昇翰


Le-Ngoc Duy


羅德煒


林易鴻


翁允中


陳譽


歷屆學生
姓名
畢業年度
研究論文
服務單位
林易賢
博士 102年
應用無刷雙饋式磁阻發電機於波浪能轉換器之研究
台達電
徐佑銓
博士 98年
應用於風力發電系統之永磁發電機設計建模與驗證
台達電
賴建欣
碩105
高子睿
碩105
呂怡萱
碩105
古佳正
碩105
張晉瑋
碩105
阮太豪
碩104
阮明發
碩104
杜慶鴻
碩104
鐘裕勛
碩104
張曜昕
碩103
陳名輝
碩103
應用磁電耦合分析之同步磁阻馬達驅動器研製
蔡逸文
碩103
應用薄型電磁鋼片之同步磁阻電機設計
李育賢
碩103
趙妍婷
碩102
陳柏廷
碩102
黃成影
碩102
翁佑甯
碩102
李羿霆
碩101
陳俊宏
碩101
李協祐
碩101
金書安
碩100
尹卡羅
碩100
林清國
碩100
高溫超導發電機之最佳化設計
林佳慶
碩99
陳韋祐
碩99
張偉隆
碩99
賴康裕
碩98
陳泊翰
碩98
余守龍
碩98
許豐聖
碩97
林繼謙
碩97
廉堯閔
碩97
許均豪
碩97
顏宏諭
碩96
葉雨涵
碩96
李奇錄
碩96
王盛篁
碩95
胡凱翔
碩95
林依蓉
碩95
陳柏勳
碩95
徐佑銓
碩94
江嘉榮
碩94
廖鴻儒
碩94
許裕昇
碩93
吳孟杰
碩93
王舜民
碩93
黃柏儒
碩104
黃健敉
碩103
應用於壓縮機之同步磁阻馬達設計與開發(產碩班)
傅健綸
碩103
多極式轉子切換磁阻馬達之設計與分析(產碩班)
曾逸誠
碩103
解角器之高解析倍頻控制設計(產碩班)
陳運鴻
碩102
教學課程
《上學期課程》
  • 電機機械設計
  • 電機機械設計
  • 電機概論實驗
  • 電機概論實驗
    《下學期課程》
  • 待定
  • 待定